|
The latest update is packaged into an install program. The size of this install program is 21 megabytes. Updates are accumulative. That means that all issues/fixes/additions listed below are contained in the latest update file. After downloading the install file, double-click on the file and install the contents into your current RouterSim NetVis4 BSCI directory. You do not need to remove your license before applying the latest update.
September '07 Update (build 4.0.38) Fixed issue where the update was not installing correctly for a specific version of the program. June '07 Update (build 4.0.37) Fixed issue with "clock set" command to allow the year to be greater than 2005 October '06 Update (build 4.0.36) Fixed issue with VLSM working with classful protocols (Rip V1, IGRP) when it should not. Fixed issue with "show ip route" command returning "%Incomplete Command". October '06 Update (build 4.0.35) Fixed issue with debug ip rip not displaying output. May '06 Update (build 4.0.34) Fixed issue with the "show ip ospf neighbor" command to handle multiple areas correctly. Fixed issue with the "show ip eigrp neighbors" command not working. Fixed issue with the "show ip ospf interface" command displaying the incorrect network state. January '06 Update (build 4.0.33) Fixed issue with maximum number of concurrent network users being reached prematurely. December '05 Update (build 4.0.32) Fixed unable to load file problem with a network configured with OSPF Authentication. Fixed the "% Incomplete command" error when executing the "show ip ospf interface" command. Fixed the "% Incomplete command" error when executing the "copy run start" command in a network with default networks configured. Fixed problem with various "show cdp ...." commands to only show CDP data if a serial connection is using the same encapsulation protocol. Fixed the "show vtp counters" command to display the correct information. Fixed problem with the default 3550 Switch name defaulting to "Switch 3550 A" when added to network. December '05 Update (build 4.0.31) Fixed ability to backspace when entering a password on a switch. Fixed the "% Incomplete command" error when executing the "show ip eigrp neighbors" command. Fixed problem with some interface configurations not being copied using the "copy run start" command. Fixed the "no frame-relay map" command to actually remove a frame-relay map. Fixed unable to load file problem with a network configured with NAT. Fixed problem with "debug ip rip" command and "debug ip rip events" command still showing RIP updates being broadcast from an interface set to be a passive-interface. Fixed problem with "show cdp neighbors" command and "show cdp neighbors detail" command displaying the correct information if a connected device or interface does not have an ip address configured. Fixed issue where the ip helper address(s) were not showing up in the "show ip interface" command. Fixed unable to load file problem with a network configured with OSPF authentication. May '05 Update (build 4.0.30) Show ip ospf border-routers command was not working under certain conditions Program now supports resolutions up to 1500 x 1000 Added support for "shutdown" and "no shutdown" commands on FastEthernet interfaces in all switches April '05 Update (build 4.0.29) Networks with zero in octets 2 or 3 were causing the program to lock up in DHCP April '05 Update (build 4.0.28) The show ip eigrp topology command would not produce output in certain situations The show ip eigrp neighbors command was not showing routers on direct connects Certain pings failed if the router port had no ip address but did have an address on a subinterface and the router was using a non-direct connect route from its routing table. Fixed loading problem with certain networks containing access lists Fixed problem with loading saved networks. March '05 Update (build 4.0.27) The show run command was not displaying the correct outgoing port name for a frame relay route on a serial interface. February '05 Update (build 4.0.26) Certain OSPF networks faiedl to load/save. January '05 Update (build 4.0.25) Fixed problem where ping stops working on direct connects when non-stub routers use default routes. Speeded up traceroute output for case where trace fails. The write memory command stopped working after configuring an ospf process and adding an area 0. This program could not load certain existing 4.0 network files. Fixed problem with ping failing in certain combinations of routers with switches. December '04 Update (build 4.0.24) Because of a current platform bug, In new installs, tooltips are now off by default. This update turns them off by default. November '04 Update (build 4.0.23) Fixed saving/loading an IP Host names on a Switch. Removed “.rsm” part of network name in the Network Visualizer title bar. Added the summarization lab. Fixed bug where the “show ip ospf neighbor command” was not always available. November '04 Update (build 4.0.22) Gateway of last resort was not being set in show ip route command when a default route was entered November '04 Update (build 4.0.21) OSPF routing updates was not working properly when OSPF routers have switches in between. Show ip ospf neighbor was not displaying correct output under some situations. Also, show ip ospf interface command was not displaying value of port priority. Fixed problem with the default ip gateway not showing in the show run output for 2950 switches Console label would “flash” and not display the correct label when running the reload command on a router. Fixed problems with pinging from Host in some NAT network configurations. Sometimes ”Incomplete Command" error message would display when trying to assign an ospf routing protocol. Network nodes now have tooltips with a user option to turn tooltips on/off. October '04 Update (build 4.0.20) Ping was working even when the destination router did not have a route back to the router that did the ping. Gateway of last resort was not being set in show ip route command when a default route was entered. Packets were shown as being sent out of a passive rip interface by the Netpacket Monitor. October '04 Update (build 4.0.19) Pre-configured CCNA Practice Sim OSPF network better matchs lab. Under some conditions, BSCI networks built from devices dragged off of the device list would not ping or otherwise function properly. Some cross-connected OSPF router networks would hang the application when setting configurations. October '04 Update (build 4.0.18) Lab 10.7 - configured devices could not ping each other. August '04 Update (build 4.0.17) Added the Net Packet Monitor. August '04 Update (build 4.0.16) Added the 3550 switch August '04 Update (build 4.0.15) Fixed issue with not being able to save a network Fixed issue with program closing prematurely August '04 update (build 4.0.14) Fixed issue in Extended Lab 6.25 where hosts weren’t able to ping each other. Fixed issue where a packet wasn’t getting through all interfaces on a 2950 Switch. August '04 update (build 4.0.13) Fixed issue where packets not getting through subinterfaces. Fixed issue where hosts were able to ping outside their respective VLANs when they shouldn’t. Fixed issue in “show ip eirgp neighbors” command displaying “incomplete command”. Fixed issue where a saved network with default routes and OSPF wouldn't load properly. July '04 update (build 4.0.12) Added CCNA practice sim labs for access lists, OSPF & RIP. Added the “show spanning-tree interface fastethernet 0/<1-12> switchport” command. Added the “spanning-tree vlan <1-1005> priority <0-61440>” command. Added support for Cisco Academy semester #3 labs 8.1 & 8.2 Added DHCP support including “dhcp-config” mode. Added the “ip dhcp pool WORD” command. Added commands “network A.B.C.D A.B.C.D”, “default-router A.B.C.D”, “dns-server A.B.C.D”, “domain-name WORD”, & “netbios-name-server A.B.C.D” in the “dhcp-config” mode. Added the “ip dhcp excluded-address A.B.C.D A.B.C.D” command. Added the “show ip dhcp binding” command. Added the “ipconfig” command in the host. Added the “ip helper-address” command. Added the “debug ppp tasks” command. Added the “debug ppp negotiation” command. Added the “encapsulation frame-relay ietf” command. Added the “keepalive” command. Added the “frame-relay map ip A.B.C.D <1-132> ietf broadcast” command. Added support for Cisco Academy semester #4 labs 11.7,13.4,13.5,15.2 & 15.4. Fixed bug with a cross connected network causing the message “% Unrecognized host or address or protocol not running” on a ping that should have worked. Fixed bug with connecting devices and disconnecting devices. June '04 Update Bug fixed where an endless loop occurred when packets were sent through.a network where two or more devices are connected more than once. May '04 Update (build 4.0.11) Added the “show interface fastethernet 0/<1-12> switchport” command. Added the “vtp server” command in the Vlan database mode of the 2950 Switch. Added the “vtp client” command in the Vlan database mode of the 2950 Switch. Added the “vtp domain” command in the Vlan database mode of the 2950 Switch. Added support for Cisco Academy semester #3 labs 9.3,10.2,10.3 & 10.4 Added all network layouts for Cisco Academy semester #4. Added support for Cisco Academy semester #4 labs 11.1,11.2,11.3,11.4,11.5,13.1,13.2 & 13.3. May '04 Update (build 4.0.10) Added the “ip http server” command for the 1900 Switch. Added the “show mac-address-table” command. Added the “clear mac-address-table dynamic” command. Added the “mac-address-table static H.H.H vlan 1 interface fastethernet 0/<1-12>” command. Added the “mac-address-table permanent H.H.H ethernet 0/<1-12>” command. Added the “show mac-address-table static” command. Added the “switchport port-security” command. Added the “switchport port-security mac-address sticky” command. Added the “port secure” command. Added the “show port-security” command. Added the “show mac-address-table security” command. Added the “switchport port-security maximum <1-132>” command. Added the “port secure mac-mac-count <1-132>” command. Added the “switchport port-security violation shutdown” command. Added support for Cisco Academy semester #3 labs 7.2, 7.3, 7.4, 7.5 & 7.6. April '04 Update (build 4.0.9) Fixed issue with loading and IGRP network from a file. Fixed issue with creating a sub interface. Fixed issue with devices disappearing after being dragged and dropped. April '04 Update (build 4.0.8) Added the “area <0-4294967295> authentication” command. Added the “show ip eigrp topology all-links” command. Added the “show ip eigrp topology A.B.C.D” command. Added the “show interface vlan 1” command. Added the “show flash” command. Added the “dir flash” command. Added the “show ip interface vlan 1” command. Fixed issue with routes not updating after issuing a “reload” command. Added support for Cisco Academy semester #3 labs 3.2, 3.4, 4.2 & 7.1. April '04 Update (build 4.0.7) Added support for Border Gateway Protocol (BGP). Added the “router bgp <1-65535>” command. Added the “neighbor A.B.C.D remote-as” command. Added the “synchronization” command. Added the “auto-summary” command. Added the “show ip bgp” command. Added the “show ip bgp summary” command. Added the “show ip route connected” command. Added the “ip subnet-zero” command. Added the “show ip ospf interface fastethernet 0/0” command. Added the “debug ip ospf event” command. Added all network layouts for Cisco Networking Academy semester #3. Fixed issue with directly connected devices not checking subnet masks on pings. March '04 Update (build 4.0.6) Added the “access-list <100-199> deny tcp any host A.B.C.D eq 23” command Fixed a situation with specific network layouts where the program would "hang". March '04 Update (build 4.0.5) Added the “ip http server” command Added the “ip access-list standard” command Added the “deny command Added the “permit” command Added the “reload in” command Added 16 new variations of the “access-list’ command Added the “clear access-list counters” command Added the “show ip route connected” command Added the “end” command in all config modes Added support for the CTRL-C key in the console Added network layouts for labs within Cisco Networking Academy Lab 20 for semster 2 February '04 Update (build 4.0.4) Added the “ip default-network” command Added the “variance” command Added the “show ip rip database” command Fixed issue with saving a network (involved using sub interfaces and executing a “copy run start”) Completed commands for Cisco Academy Labs 16 and 18 for semester 2 February '04 Update (build 4.0.3) Added the “passive-interface” command Added the “debug ip rip database” command Added the “debug ip rip events” command Added the “debug ip rip trigger” command Added the “ip route-cache” command Added the “debug ip packet” command Added the “default-information originate” command Added the “show ip route igrp” command January '04 Update (build 4.0.2) Added NAT/PAT functionality. Includes commands – “ip nat pool”, “ip nat inside source”, “ip nat inside”, “ip nat outside”, “clear ip nat statistics”, “clear ip nat transactions”, “show ip nat statistics”, “show ip nat translations”, and “debug ip nat” Added new variations of the “access-list” command Added the “show ip interface brief” command Updated the “ip host” command to accept up to 8 ip addresses Added “show cdp interface” command Added “show cdp entry * protocol” command Added “debug cdp packets” command Added “clear cdp counters” command Added “no hostname” command Added “tracert” command on the host Added “no debug all” command Pasting text into console ignores lines that start with “!” Added network layouts for Cisco Academy semester # |
